Locomotive cabs

General discussion about locomotives, rolling stock, and equipment

Moderator: John_Perkowski

Post Reply
atsf sp
Posts: 2181
Joined: Mon Jul 30, 2007 7:00 pm

Re: Locomotive cabs

Post by atsf sp » Mon Aug 10, 2015 9:45 pm

SD45 looks like a sd40 interior
"Why would you take a train to go see another train?"
Some people just don't understand.
My Photos

Posts: 449
Joined: Sun Apr 06, 2008 5:09 pm

Re: Locomotive cabs

Post by slashmaster » Mon Oct 05, 2015 9:49 pm

Is this a small perhaps 2 foot gauge locomotive in this pic? It's yellow on the right. https://www.facebook.com/mgtowtechnique ... =3&theater" onclick="window.open(this.href);return false;

Posts: 3629
Joined: Fri Mar 19, 2004 12:41 am

Re: Locomotive cabs

Post by nyandw » Tue Apr 24, 2018 11:33 am

Some cab shots:http://www.trainsarefun.com/lirr/lirrcab.htm

ALCO C420 control stand c.1968 (Jay Bendersky-Robert Anderson)


1) Throttle-idle position
2) Dynamic Brake handle-locked out not used
3) Automatic Brake valve-train brake
4) Independent Brake valve-full applied position
5) Head Light switch-rear
6) Head Light switch-front
7) Bell valve
8) Console Light
9) Manual sander valve
10) Console Light
11) Emergency fuel cut off switch
12) Switches-Control-battery-generator field-fuel pump
13) Reverser
14) Air brake gauge-Main Res/Equalizing res
15) Air Brake gauge-Brake pipe/Brake cylinder
16) Air Brake gauge-Supression air
17) Air Brake gauge-Timing Air
18) Amp gauge-Traction
19) Two Horn chains encased in rubber hose-city/country(1)
20) Brake pipe regulating valve
21) ABVCOC (Automatic Brake Valve Cut-Out Cock)
22) Independent brake regulating valve
23) MU2a valve-multiple unit/lead-dead

Note (1): There were two ropes with a length of rubber hose (about 18" each) on them where you would pull them down to sound the horn. One was for the "City" tone, which was lower in volume than the other, "Country" tone which was louder. Both ropes led to separate valves on the cab ceiling. If you grabbed them both together, you could make even more noise.

Further trivia: Because of clearance issues at various locations, the horns were mounted on the engineers side of the car body, on the side (not the top) of the engine, just ahead of the smoke deflectors.

Posts: 3629
Joined: Fri Mar 19, 2004 12:41 am

Locomotive cabs: DE/DM Cab

Post by nyandw » Thu Aug 30, 2018 9:09 pm

DE/DM Simulator Cab at OBRM photos: http://www.trainsarefun.com/lirr/lirrex ... ralist.htm" onclick="window.open(this.href);return false;

Posts: 65
Joined: Wed May 31, 2017 2:04 pm

Re: Locomotive cabs

Post by phillyrube » Thu Aug 08, 2019 3:33 pm

Took the grandson out yesterday to ride the Sunrail in Orlando, FL. Cruised from Winter Park to Kissimmee, cab end controls, then Kissimmee to Debary, engine in front. Coming back from Debary we sat up front next to the control cab. Door was open, so we could see the driver work. Engine is a MPI MP32PH-Q. On the southbound stretch it's a pusher. Pretty much figured out the controls: alarm ack on the floor, brake on the left, reverse in the center, throttle on the right. Left side has controls like the bell flashing ditch lights. Horn in the center of the desk.

Two large digital gauges, air pressure and speedo. Had a Wabtec screen that said GPS, but no map. Displayed digital speed. Part of the PTC?

When stopped, she locked the brakes, put reverse in neutral, idle low. Starting up, brakes off forward, throttle moved up between green and red. Coasting, pulls throttle back. Going to stop, applies brakes a bit, then moves throttle back up? Regenerative?

Crews were good, professional , trains clean, ran smoothly. Had a great time.

Post Reply

Return to “General Discussion: Locomotives, Rolling Stock, and Equipment”